Molds tend to grow at homes and affect the general health of those living in it as well as affect the appearance of the house. However one needs to be sure that molds are actually affecting the house. These can be easily done through using Mold Testing Illinois kits. The article below explains some of the types and how they are used.
The kits can either test the type of molds, if they are molds while others check both. As with the lift tape kits, they use a tacky and sticky surface to test the type of the molds. The tacky surface covers the sticky one which is placed onto the molds and then recovered by the tacky surface. The user then takes the tape to a laboratory where the exact type of molds is identified.
The next type of kit is used to check if there are molds. It includes a swab in a test tube and is names the instant kit. The swab is usually rubbed onto the surface that one suspect could be molds then returned into the tube. It is acceptable to set for approximately ten minutes then after that the owner can compare the color of the test tube with that presented in the color chart provided with the kit to analyze the results.
An alternative kit that does the tests confirmed by both the instant and lift tape set is the viable kit. It confirms the molds presence and also their types. To use the kit, the swab is rubbed onto the surface that is suspected to be moldy then also rubbed on a gel like substance stored in a petri dish for the kit. The dish is afterwards closed for between 3 to 7 days to allow molds to grow for observation to determine if they are present or not.
The viable kit also tests air quality. To do this, two kits will be required. One of the petri dishes will be placed outside next to the room where the other petri dish is to be placed. The dishes are then opened for an hour and later closed for 7 days for molds to grow. If the results in the petri dishes are the same, there is no need to worry however of they are very different, then laboratory tests will be required.
The same kit can also be used to check the heating and cooling system of the home. To do this, all the vents should be closed except the one that is far away from the system. The kit is placed on the vent that is left open; the system is then switched on to maximum setting. Allow the system to run in this setting for ten minutes then remove the dish. Close it and check it after 7 days for molds growth.
After noticing the presence of molds, many people will automatically try to remove them. This is very hazardous to their health especially if they are not sure of the exact types of molds. Some of them are very poisonous and their removal without the necessary precautions can lead to dire consequences. An expert is thus the best person to remove molds.
Molds have been known to lead to high allergies if left not contained with itchy skin and irritated eyes as a common sign of molds. For other people they tend to worsen their conditions example asthma.
The kits can either test the type of molds, if they are molds while others check both. As with the lift tape kits, they use a tacky and sticky surface to test the type of the molds. The tacky surface covers the sticky one which is placed onto the molds and then recovered by the tacky surface. The user then takes the tape to a laboratory where the exact type of molds is identified.
The next type of kit is used to check if there are molds. It includes a swab in a test tube and is names the instant kit. The swab is usually rubbed onto the surface that one suspect could be molds then returned into the tube. It is acceptable to set for approximately ten minutes then after that the owner can compare the color of the test tube with that presented in the color chart provided with the kit to analyze the results.
An alternative kit that does the tests confirmed by both the instant and lift tape set is the viable kit. It confirms the molds presence and also their types. To use the kit, the swab is rubbed onto the surface that is suspected to be moldy then also rubbed on a gel like substance stored in a petri dish for the kit. The dish is afterwards closed for between 3 to 7 days to allow molds to grow for observation to determine if they are present or not.
The viable kit also tests air quality. To do this, two kits will be required. One of the petri dishes will be placed outside next to the room where the other petri dish is to be placed. The dishes are then opened for an hour and later closed for 7 days for molds to grow. If the results in the petri dishes are the same, there is no need to worry however of they are very different, then laboratory tests will be required.
The same kit can also be used to check the heating and cooling system of the home. To do this, all the vents should be closed except the one that is far away from the system. The kit is placed on the vent that is left open; the system is then switched on to maximum setting. Allow the system to run in this setting for ten minutes then remove the dish. Close it and check it after 7 days for molds growth.
After noticing the presence of molds, many people will automatically try to remove them. This is very hazardous to their health especially if they are not sure of the exact types of molds. Some of them are very poisonous and their removal without the necessary precautions can lead to dire consequences. An expert is thus the best person to remove molds.
Molds have been known to lead to high allergies if left not contained with itchy skin and irritated eyes as a common sign of molds. For other people they tend to worsen their conditions example asthma.
About the Author:
Find a list of the benefits you get when you use mold testing Illinois services and more info about a reputable service provider at http://www.moldprochicago.com/moldprochicago.com/mold-services today.
No comments:
Post a Comment